HL INSTALL B3 E90, INSTRUKCJE
[ Pobierz całość w formacie PDF ]
//-->Headlight Removal & Installation: BMW E90 (3 Series)DISCLAIMERBuyer assumes any and all risk and liability from the installation and use of this product. Seller, author, or any of their affiliatesassume no liability for injury, loss, incidental or consequential damages deriving from installation and/or use of this product.Tools Required:•8mm or 5/16” socket•3/8” or 1/4” socket extension (6” length)•3/8” or 1/4” drive socket wrench•Flathead Screwdriver•Phillips Screwdriver•Star-shaped driverStep 1:Removetwo torxscrewsthat are mounted ontop of your headlight'shousing using a Star-shapedtorx driver.Step 2:Next,unclipfourtorx screwson top of theBumper (above the frontkidney grille)Step 3:You must alsounclipandunscrewtwo “clip #1 inthe photo / torx screw #2 in the photo”from each tirewells and a clip remover. The clip and screw are foundnear the outer-edge of each front-side tire wells.Step 4:After you have removed the two screws fromStep3,then you must carefully pull back the Mud-guard (shown asFigure 1below; between fender and bumper) toreveal thetwo torx screwsattached to the Bumper (shown asFigure 2below). Locate these screws and unscrewthem.Figure 1Figure 2Step 5:There is an additional 8mmscrew on each side(numbered 1 in the picture below) you need tounscrewbefore moving on to the next step. The screw can be found deeper inside the tire well. It should be situated onthe back-side of the bumper and in front of your car’s Springs/Coils.Step 6:There aresix 8mm screwsyou mustunscrewbefore moving on to the next step. The six screws aresituated underneath the Bumper. The photo to the left shows where the screws would have been after bumperremoval.*Please do not forget to remove screws under the bumper, before continuing on to the next step.Step 7:Next, you mustpull-out and uncliptheHeadlight washer caps.As shown below, there aretwoHeadlight washer capsunder each Headlight on your car’s front Bumper. Very carefully using yourFlatheadScrewdriver,pry open the square-like cap and carefully pull-out the plastic hinge. Once you have pulled-out theplastic hinge (just enough so that you may unclip it) go ahead and unclip theHeadlight washer caps.Be carefulnot to mix theHeadlight washer caps,know which washer belongs to which side.Step 8:After you have unclipped theHeadlight washer caps,you may then remove the Bumper. Starting fromone side of your tire-well, carefully work your way around your bumper to the opposite tire-well side by gentlypulling your bumper away from your car frame.*Pleasemake sure you have taken off all of the necessary screws before removing the Bumper.*Makesure to place the bumper somewhere safe and away from your work-space.Step 9:Once the Bumper has been removed and placed somewhere safe, you must unscrewtwo screws(numbered 1 and 2 inFigure 3below) from the front-side grille using a Phillips screwdriver.Figure 3Step 10:After you have removed the screws fromStep 9,you must try and see if the Headlight housing can bemoved. Please note that there isone more screw(numbered 1 in the example below) that needs to be unscrewedbefore fully detaching the Headlight housing from the car. The torx screw can be found at the base of theHeadlight’s housing.Step 11:Once you have unscrewed the screw on the base of the Headlight’s housing, you mustun-plugtheHeadlight’swiring adapter.The wiring adapter can be found situated in the back of the Headlight’s housing.After you have unplugged the wiring adapter, you will be able to remove the Headlight and its housing. [ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
//-->Headlight Removal & Installation: BMW E90 (3 Series)DISCLAIMERBuyer assumes any and all risk and liability from the installation and use of this product. Seller, author, or any of their affiliatesassume no liability for injury, loss, incidental or consequential damages deriving from installation and/or use of this product.Tools Required:•8mm or 5/16” socket•3/8” or 1/4” socket extension (6” length)•3/8” or 1/4” drive socket wrench•Flathead Screwdriver•Phillips Screwdriver•Star-shaped driverStep 1:Removetwo torxscrewsthat are mounted ontop of your headlight'shousing using a Star-shapedtorx driver.Step 2:Next,unclipfourtorx screwson top of theBumper (above the frontkidney grille)Step 3:You must alsounclipandunscrewtwo “clip #1 inthe photo / torx screw #2 in the photo”from each tirewells and a clip remover. The clip and screw are foundnear the outer-edge of each front-side tire wells.Step 4:After you have removed the two screws fromStep3,then you must carefully pull back the Mud-guard (shown asFigure 1below; between fender and bumper) toreveal thetwo torx screwsattached to the Bumper (shown asFigure 2below). Locate these screws and unscrewthem.Figure 1Figure 2Step 5:There is an additional 8mmscrew on each side(numbered 1 in the picture below) you need tounscrewbefore moving on to the next step. The screw can be found deeper inside the tire well. It should be situated onthe back-side of the bumper and in front of your car’s Springs/Coils.Step 6:There aresix 8mm screwsyou mustunscrewbefore moving on to the next step. The six screws aresituated underneath the Bumper. The photo to the left shows where the screws would have been after bumperremoval.*Please do not forget to remove screws under the bumper, before continuing on to the next step.Step 7:Next, you mustpull-out and uncliptheHeadlight washer caps.As shown below, there aretwoHeadlight washer capsunder each Headlight on your car’s front Bumper. Very carefully using yourFlatheadScrewdriver,pry open the square-like cap and carefully pull-out the plastic hinge. Once you have pulled-out theplastic hinge (just enough so that you may unclip it) go ahead and unclip theHeadlight washer caps.Be carefulnot to mix theHeadlight washer caps,know which washer belongs to which side.Step 8:After you have unclipped theHeadlight washer caps,you may then remove the Bumper. Starting fromone side of your tire-well, carefully work your way around your bumper to the opposite tire-well side by gentlypulling your bumper away from your car frame.*Pleasemake sure you have taken off all of the necessary screws before removing the Bumper.*Makesure to place the bumper somewhere safe and away from your work-space.Step 9:Once the Bumper has been removed and placed somewhere safe, you must unscrewtwo screws(numbered 1 and 2 inFigure 3below) from the front-side grille using a Phillips screwdriver.Figure 3Step 10:After you have removed the screws fromStep 9,you must try and see if the Headlight housing can bemoved. Please note that there isone more screw(numbered 1 in the example below) that needs to be unscrewedbefore fully detaching the Headlight housing from the car. The torx screw can be found at the base of theHeadlight’s housing.Step 11:Once you have unscrewed the screw on the base of the Headlight’s housing, you mustun-plugtheHeadlight’swiring adapter.The wiring adapter can be found situated in the back of the Headlight’s housing.After you have unplugged the wiring adapter, you will be able to remove the Headlight and its housing. [ Pobierz całość w formacie PDF ]