HMI MV4 – PLC Communication ...

[ Pobierz całość w formacie PDF ]
MV4 – PLC Communication
via SUCOM-A, Suconet K, PROFIBUS-DP
MV4 Communication Cards
and Configuration of MV4 and PLC
07/01 AWB-C2700-1349GB
1
st
published 1999, edition 01/99
2
nd
published 2000, edition 05/00
3
rd
published 2001, edition 07/01,
See list of revisions on page II
© Moeller GmbH, Bonn
Authors: Norbert Mausolf, Oswald Weiß
Translators: T. Osborn, D. Long
All brand and product names are
trademarks or registered trademarks of the
owner concerned.
All rights reserved, including those of the
translation.
No part of this manual may be reproduced in
any form (printed, photocopy, microfilm or
any otherprocess) or processed, duplicated
or distributed by means of electronic
systems without written permission of
Moeller GmbH, Bonn.
Subject to alterations without notice.
Caution!
Dangerous Electrical Voltage!
Before commencing the installation
Disconnect the power supply of the
device.
Ensure that devices cannot be
accidentally restarted.
Verify isolation from the supply.
Earth and short circuit.
Cover or enclose neighbouring units that
are live.
Follow the engineering instructions
(AWA) of the device concerned.
Only suitably qualified personnel may
work on this device/system.
Before installation and before touching
the device ensure that you are free of
electrostatic charge.
Connecting cables and signal lines
should be installed so that inductive or
capacitive interference do not impair the
automation functions.
Install automation devices and related
operating elements in such a way that
they are well protected against
unintentional operation.
Suitable safety hardware and software
measures should be implemented for the
I/O interface so that a line or wire
breakage on the signal side does not
result in undefined states in the
automation devices.
Ensure a reliable electrical isolation of
the low voltage for the 24 volt supply.
Only use power supply units complying
with IEC 60 364-4-41 or HD 384.4.41 S2.
Deviations of the mains voltage from the
rated value must not exceed the
tolerance limits given in the
specifications, otherwise this may cause
malfunction and dangerous operation.
Emergency stop devices complying with
IEC/EN 60 204-1 must be effective in all
operating modes of the automation
devices. Unlatching the emergency-stop
devices must not cause uncontrolled
operation or restart.
Devices that are designed for mounting
in housings or control cabinets must only
be operated and controlled after they
have been installed with the housing
closed. Desktop or portable units must
only be operated and controlled in
enclosed housings.
Measures should be taken to ensure the
proper restart of programs interrupted
after a voltage dip or failure. This should
not cause dangerous operating states
even for a short time. If necessary,
emergency-stop devices should be
implemented.
I
List of modifications to the manual AWB-C2700-1349GB
Edition
Page
Description
New
Modification
Omitted
07/01
14
Note
II
Contents
About This Manual
3
Contents
3
Target group
3
1 Communication Cards
4
ZB 4-601-IF1/ZB 4-609-IF1
5
ZB 4-604-IF1
11
2 Communication Cables
14
Overview
14
MV 4 – PC (configuration)
15
MV 4 – PLC via SUCOM-A
16
MV 4 – PLC via Suconet K
17
MV 4 – PLC via PROFIBUS-DP
18
3 Principle of Communication
19
Communication links
19
Data exchange principle
20
4 MV 4 – PLC via SUCOM A
22
Device interfaces
22
Data ranges
22
Defining the communication link
23
Online diagnostics
24
5 MV 4 – PLC via Suconet K
25
Device interfaces
25
Data ranges
25
Defining the communication link
26
Online diagnostics
30
1
Contents
6 MV 4 – PLC via PROFIBUS-DP
32
Device interfaces
32
Data ranges
32
Defining the communication link
33
Online diagnostics
37
7 Commissioning
39
Index
41
2
[ Pobierz całość w formacie PDF ]

zanotowane.pl

doc.pisz.pl

pdf.pisz.pl

chiara76.opx.pl