HP4700 4730TECH, Drukarki, HP
[ Pobierz całość w formacie PDF ]
HP4700TECH
Technical Instructions
Printers
OEM Info
Tools
1
CORPORATE
LOS ANGELES, USA
See Last Page for Info.
See Last Page for Info.
See Last Page for Info.
US 1 800 394.9900
Int’l +1 818 837.8100
FAX 1 800 394.9910
Int’l +1 818 838.7047
Photo 1
Cartridge Disassembly:
ATLANTA, USA
US 1 877 676.4223
Int’l +1 678 919.1189
FAX 1 877 337.7976
Int’l +1 770 516.7794
Step 1
Using an X-acto knife carefully cut the plastic
caps that cover the cartridge pins on each side of
the cartridge.
KANSAS CITY, USA
US 1 913 871.1700
FAX 1 913 888.0626
(See Photos 1 & 2)
MIAMI, USA
US 1 800 595.4297
Int’l +1 305 594.3396
FAX 1 800 522.8640
Int’l +1 305 594.3309
Photo 2
NEW YORK, USA
US 1 800 431.7884
Int’l +1 631 588.7300
FAX 1 800 431.8812
Int’l +1 631 588.7333
TORONTO, CAN
CAN 1 877 848.0818
Int’l +1 905 712.9501
FAX 1 877 772.6773
Int’l +1 905 712.9502
BUENOS AIRES, ARG
ARG 0810 444.2656
Int’l +011 4583.5900
FAX +011 4584.3100
Photo 3
Step 2
Using a 5/64” drill bit, drill two small holes next
to the cartridge pins on each side of the
cartridge.
MELBOURNE, AUS
AUS 1 800 003. 100
Int’l +62 03 9561.8102
FAX 1 800 004.302
Int’l +62 03 9561-7751
(See in Photo 3 and Photo 4)
SYDNEY, AUS
AUS 1 800 003.100
Int’l +62 02 9648.2630
FAX 1800 004.302
Int’l +62 02 9548.2635
MONTEVIDEO, URY
URY 02 902.2001
Int’l +5982 902.2001
FAX +5982 900.0858
Photo 4
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX +27 11 974.3593
SÃO PAULO, BRAZIL
Int’l +55 11 5524.8000
RAANANA, ISRAEL
ISR 09 760.12.39
Int’l +972 9760.12.39
ISR 052.38.555.82
Int’l +972 5238.555.82
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
REV. 5/01/07
2
HP4700 Technical Instructions
Photo 8
Step 5
Separate the two sections of the cartridge by
carefully lifting the waste hopper up away from
the toner hopper.
(See Photo 8)
Set the toner
hopper aside.
Step 3
Using needle nose pliers, remove
the cartridge pins from the
cartridge.
(See Photos 5 & 6)
Photo 5
Photo 9
Waste Hopper Disassembly:
Step 6
Place the waste hopper on the workbench with
the drum facing up and the drum shutter
towards you. Slide the drum shutter open (up).
Remove the drum shutter bar from its position-
ing holes on each side of the waste hopper.
(See Photos 9 & 10)
Photo 6
Photo 10
Step 4
Using a spring hook, release the
cartridge tension spring from its
post on the contact side of the
cartridge.
(See Photo 7)
Photo 11
Step 7
Remove the drum shutter from the drum shut-
ter arm.
(See Photo 11)
Photo 7
Photo 12
Step 8
Using a pin removal tool, remove the roll pin
that holds the drive element to the drum axle.
(See Photo 12)
Set the roller pin aside so you
don’t lose it.
HP4700 Technical Instructions
3
Photo 13
Step 9
Pull the drive element from the drum axle.
(See Photo 13
)
Step 14
Using needle nose pliers remove
the pins.
(See Photo 19 & 20)
Photo 19
Photo 14
Step 10
Rotate the drum so the roll pin holding the drum
in place sits horizontal. Using the pin removal
tool remove the pin that locks the drum in posi-
tion.
(See Photo 14)
Set the roll pin aside.
Photo 20
Photo 15
Step 11
Push the drive side of the drum axle into the
drum. While holding the drum, pull the drum
axle from the contact side of the waste hopper.
(See Photo 15
) Set the drum axle aside.
Step 12
Remove the drum from the waste hopper.
(See Photo 16)
Step 15
Lift up the PCR retaining arms and
remove the PCR from the PCR
saddles.
(See Photo 21)
Remove
the retaining arms from the ends of
the PCR.
(See Photo 22)
Clean the
PCR using a dry lint free cloth.
Photo 16
NOTE:
If you plan on reusing the OEM drum
place the drum in a protected area out of the
light.
Photo 21
Step 13
Using the 5/64” drill bit drill two holes next to
the pins that hold the PCR retaining arms on
each side of the waste hopper.
(See Photos 17 & 18)
Photo 18
Photo 17
Photo 21
4
HP4700 Technical Instructions
Photo 26
Step 19
Clean the waste hopper using dry compressed
air or a vacuum.
Step 16
Using a # 2 Phillips screwdriver
remove the two screws holding the
wiper blade.
(See Photo 23)
Waste Hopper Reassembly:
Step 20
Clean the PCR saddles using a cotton swab
and alcohol.
(See Photo 26)
Photo 23
Photo 27
Step 21
Clean the OEM wiper blade sealing material
using a lint free cloth and alcohol.
(See Photo 27)
This will make it tacky again allowing it to stick
to the wiper blade once the blade is installed.
Step 17
Grab the wiper blade using needle
nose pliers. Carefully lift the wiper
blade leaving the OEM sealing
material stuck to the waste hopper.
(See Photo 24)
Clean the wiper
blade using dry compressed air.
Photo 28
Step 22
Install the two wiper blade shims to each side
of the waste hopper.
(See Photo 28)
Photo 24
Photo 29
Step 23
Apply yellow toner to the end of the wiper
blade instead of padding powder. Place the
wiper blade onto the waste hopper and install
the two screws that hold the blade in place.
(See Photo 29)
Step 18
Remove the wiper blade shims
from each end of the waste hopper.
(See Photo 25)
Photo 30
Step 24
Place the PCR retaining arms onto the shaft of
the PCR so the cam on each retaining arm face
out toward the ends of the waste hopper.
(See Photo 30)
Photo 21
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
HP4700 Technical Instructions
5
Photo 31
Step 25
Install the PCR into the PCR saddles so the
white PCR retaining arm is on the gear side of
the waste hopper.
(See Photo 31
)
Step 30
Rotate the drum axle and the drum
till the hole for the pin that locks the
drum in place are aligned. Place the
roller pin into the hole. Using a pin
installation tool, install the pin
through the drums drive hub.
(See Photo 37)
Photo 32
Step 26
Install the two pins through the cam of the
PCR retaining arms on each side of the waste
hopper.
(See Photos 32 & 33)
Photo 37
Photo 33
Photo 34
Step 27
Pad the drum using a small amount of yellow
toner instead of padding powder. Place the
new or used drum onto the waste hopper so
the drive hub is on the gear side of the waste
hopper and the hole for the roller pin faces up.
(See Photo 34)
Step 31
Rotate the drum 5-10 revolutions to
ensure the drum and wiper blade
were properly lubricated so the
wiper blade does not flip. Clean the
PCR using a lint free cloth to
remove any toner that may have
gotten on the roller.
Step 32
Place the drum shutter actuator pin
into the drum shutter arm. Lift open
the drum shutter and install the drum
shutter bar into the positioning holes
on each side of the waste hopper.
(See Photos 38 & 39)
Photo 35
Step 28
Hold the drum axle so the holes for the roll pins
face up. Slide the drive side of the drum axle
through the contact end of the drum.
(See Photo 35)
Photo 38
Photo 36
Step 29
Place the drive element onto the shaft of the
drum axle so it looks like the element is point-
ing to the ceiling. Install the small roll pin into
the hole in the drive element. Using a pin tool,
install the pin into the drive element.
(See Photo 36)
Photo 39
[ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
HP4700TECH
Technical Instructions
Printers
OEM Info
Tools
1
CORPORATE
LOS ANGELES, USA
See Last Page for Info.
See Last Page for Info.
See Last Page for Info.
US 1 800 394.9900
Int’l +1 818 837.8100
FAX 1 800 394.9910
Int’l +1 818 838.7047
Photo 1
Cartridge Disassembly:
ATLANTA, USA
US 1 877 676.4223
Int’l +1 678 919.1189
FAX 1 877 337.7976
Int’l +1 770 516.7794
Step 1
Using an X-acto knife carefully cut the plastic
caps that cover the cartridge pins on each side of
the cartridge.
KANSAS CITY, USA
US 1 913 871.1700
FAX 1 913 888.0626
(See Photos 1 & 2)
MIAMI, USA
US 1 800 595.4297
Int’l +1 305 594.3396
FAX 1 800 522.8640
Int’l +1 305 594.3309
Photo 2
NEW YORK, USA
US 1 800 431.7884
Int’l +1 631 588.7300
FAX 1 800 431.8812
Int’l +1 631 588.7333
TORONTO, CAN
CAN 1 877 848.0818
Int’l +1 905 712.9501
FAX 1 877 772.6773
Int’l +1 905 712.9502
BUENOS AIRES, ARG
ARG 0810 444.2656
Int’l +011 4583.5900
FAX +011 4584.3100
Photo 3
Step 2
Using a 5/64” drill bit, drill two small holes next
to the cartridge pins on each side of the
cartridge.
MELBOURNE, AUS
AUS 1 800 003. 100
Int’l +62 03 9561.8102
FAX 1 800 004.302
Int’l +62 03 9561-7751
(See in Photo 3 and Photo 4)
SYDNEY, AUS
AUS 1 800 003.100
Int’l +62 02 9648.2630
FAX 1800 004.302
Int’l +62 02 9548.2635
MONTEVIDEO, URY
URY 02 902.2001
Int’l +5982 902.2001
FAX +5982 900.0858
Photo 4
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX +27 11 974.3593
SÃO PAULO, BRAZIL
Int’l +55 11 5524.8000
RAANANA, ISRAEL
ISR 09 760.12.39
Int’l +972 9760.12.39
ISR 052.38.555.82
Int’l +972 5238.555.82
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
REV. 5/01/07
2
HP4700 Technical Instructions
Photo 8
Step 5
Separate the two sections of the cartridge by
carefully lifting the waste hopper up away from
the toner hopper.
(See Photo 8)
Set the toner
hopper aside.
Step 3
Using needle nose pliers, remove
the cartridge pins from the
cartridge.
(See Photos 5 & 6)
Photo 5
Photo 9
Waste Hopper Disassembly:
Step 6
Place the waste hopper on the workbench with
the drum facing up and the drum shutter
towards you. Slide the drum shutter open (up).
Remove the drum shutter bar from its position-
ing holes on each side of the waste hopper.
(See Photos 9 & 10)
Photo 6
Photo 10
Step 4
Using a spring hook, release the
cartridge tension spring from its
post on the contact side of the
cartridge.
(See Photo 7)
Photo 11
Step 7
Remove the drum shutter from the drum shut-
ter arm.
(See Photo 11)
Photo 7
Photo 12
Step 8
Using a pin removal tool, remove the roll pin
that holds the drive element to the drum axle.
(See Photo 12)
Set the roller pin aside so you
don’t lose it.
HP4700 Technical Instructions
3
Photo 13
Step 9
Pull the drive element from the drum axle.
(See Photo 13
)
Step 14
Using needle nose pliers remove
the pins.
(See Photo 19 & 20)
Photo 19
Photo 14
Step 10
Rotate the drum so the roll pin holding the drum
in place sits horizontal. Using the pin removal
tool remove the pin that locks the drum in posi-
tion.
(See Photo 14)
Set the roll pin aside.
Photo 20
Photo 15
Step 11
Push the drive side of the drum axle into the
drum. While holding the drum, pull the drum
axle from the contact side of the waste hopper.
(See Photo 15
) Set the drum axle aside.
Step 12
Remove the drum from the waste hopper.
(See Photo 16)
Step 15
Lift up the PCR retaining arms and
remove the PCR from the PCR
saddles.
(See Photo 21)
Remove
the retaining arms from the ends of
the PCR.
(See Photo 22)
Clean the
PCR using a dry lint free cloth.
Photo 16
NOTE:
If you plan on reusing the OEM drum
place the drum in a protected area out of the
light.
Photo 21
Step 13
Using the 5/64” drill bit drill two holes next to
the pins that hold the PCR retaining arms on
each side of the waste hopper.
(See Photos 17 & 18)
Photo 18
Photo 17
Photo 21
4
HP4700 Technical Instructions
Photo 26
Step 19
Clean the waste hopper using dry compressed
air or a vacuum.
Step 16
Using a # 2 Phillips screwdriver
remove the two screws holding the
wiper blade.
(See Photo 23)
Waste Hopper Reassembly:
Step 20
Clean the PCR saddles using a cotton swab
and alcohol.
(See Photo 26)
Photo 23
Photo 27
Step 21
Clean the OEM wiper blade sealing material
using a lint free cloth and alcohol.
(See Photo 27)
This will make it tacky again allowing it to stick
to the wiper blade once the blade is installed.
Step 17
Grab the wiper blade using needle
nose pliers. Carefully lift the wiper
blade leaving the OEM sealing
material stuck to the waste hopper.
(See Photo 24)
Clean the wiper
blade using dry compressed air.
Photo 28
Step 22
Install the two wiper blade shims to each side
of the waste hopper.
(See Photo 28)
Photo 24
Photo 29
Step 23
Apply yellow toner to the end of the wiper
blade instead of padding powder. Place the
wiper blade onto the waste hopper and install
the two screws that hold the blade in place.
(See Photo 29)
Step 18
Remove the wiper blade shims
from each end of the waste hopper.
(See Photo 25)
Photo 30
Step 24
Place the PCR retaining arms onto the shaft of
the PCR so the cam on each retaining arm face
out toward the ends of the waste hopper.
(See Photo 30)
Photo 21
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
HP4700 Technical Instructions
5
Photo 31
Step 25
Install the PCR into the PCR saddles so the
white PCR retaining arm is on the gear side of
the waste hopper.
(See Photo 31
)
Step 30
Rotate the drum axle and the drum
till the hole for the pin that locks the
drum in place are aligned. Place the
roller pin into the hole. Using a pin
installation tool, install the pin
through the drums drive hub.
(See Photo 37)
Photo 32
Step 26
Install the two pins through the cam of the
PCR retaining arms on each side of the waste
hopper.
(See Photos 32 & 33)
Photo 37
Photo 33
Photo 34
Step 27
Pad the drum using a small amount of yellow
toner instead of padding powder. Place the
new or used drum onto the waste hopper so
the drive hub is on the gear side of the waste
hopper and the hole for the roller pin faces up.
(See Photo 34)
Step 31
Rotate the drum 5-10 revolutions to
ensure the drum and wiper blade
were properly lubricated so the
wiper blade does not flip. Clean the
PCR using a lint free cloth to
remove any toner that may have
gotten on the roller.
Step 32
Place the drum shutter actuator pin
into the drum shutter arm. Lift open
the drum shutter and install the drum
shutter bar into the positioning holes
on each side of the waste hopper.
(See Photos 38 & 39)
Photo 35
Step 28
Hold the drum axle so the holes for the roll pins
face up. Slide the drive side of the drum axle
through the contact end of the drum.
(See Photo 35)
Photo 38
Photo 36
Step 29
Place the drive element onto the shaft of the
drum axle so it looks like the element is point-
ing to the ceiling. Install the small roll pin into
the hole in the drive element. Using a pin tool,
install the pin into the drive element.
(See Photo 36)
Photo 39
[ Pobierz całość w formacie PDF ]