HTC Touch Pro - Camera removal photo guide v1.1 by A Mak, do telefonu
[ Pobierz całość w formacie PDF ]
Version 1.1
Author: A Mak a.k.a. Makuk
HTC Touch Pro Photos Guide – dismantling and removing the cameras
Tools Required
•
Small Philips Screw Driver (Optical glasses type)
•
Small Flat head screw driver (used to pry things)
•
Torq 5 (??) screwdriver (Only required to unscrew 1 torq screw)
•
Some finger nails to pry open the back casing!
There are only 4 screws holding together the back casing of the HTC touch pro. (2 at the top and 2 at the
bottom). Just remove those 4 screws and then slide your finger nails around the gap and the case will
open. Spend a little more time on the bottom of the case (i.e. near the Usb port). Note: there is a small
connector at the top left of the back PCB which connects to the speaker on the back cover. (See the
photo at the end of this guide) Carefully disconnect it from the socket to remove the back cover
completely.
The above photo shows the back casing removed.
By A. Mak 24-10-2008 - Page 1 of 27
Version 1.1
Author: A Mak a.k.a. Makuk
Close up photo of the top PCB. The Torq screw (black) is just below the Sim Card holder! (i.e. left side of
the battery connector)
By A. Mak 24-10-2008 - Page 2 of 27
Version 1.1
Author: A Mak a.k.a. Makuk
Another photo of the top PCB. You can see the torq screw clearly in the above photo (next to the battery
connector).
By A. Mak 24-10-2008 - Page 3 of 27
Version 1.1
Author: A Mak a.k.a. Makuk
A photo of the bottom PCB where the antenna cable is connected (top right).
By A. Mak 24-10-2008 - Page 4 of 27
Version 1.1
Author: A Mak a.k.a. Makuk
Another photo of the top PCB (top view).
By A. Mak 24-10-2008 - Page 5 of 27
[ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
Version 1.1
Author: A Mak a.k.a. Makuk
HTC Touch Pro Photos Guide – dismantling and removing the cameras
Tools Required
•
Small Philips Screw Driver (Optical glasses type)
•
Small Flat head screw driver (used to pry things)
•
Torq 5 (??) screwdriver (Only required to unscrew 1 torq screw)
•
Some finger nails to pry open the back casing!
There are only 4 screws holding together the back casing of the HTC touch pro. (2 at the top and 2 at the
bottom). Just remove those 4 screws and then slide your finger nails around the gap and the case will
open. Spend a little more time on the bottom of the case (i.e. near the Usb port). Note: there is a small
connector at the top left of the back PCB which connects to the speaker on the back cover. (See the
photo at the end of this guide) Carefully disconnect it from the socket to remove the back cover
completely.
The above photo shows the back casing removed.
By A. Mak 24-10-2008 - Page 1 of 27
Version 1.1
Author: A Mak a.k.a. Makuk
Close up photo of the top PCB. The Torq screw (black) is just below the Sim Card holder! (i.e. left side of
the battery connector)
By A. Mak 24-10-2008 - Page 2 of 27
Version 1.1
Author: A Mak a.k.a. Makuk
Another photo of the top PCB. You can see the torq screw clearly in the above photo (next to the battery
connector).
By A. Mak 24-10-2008 - Page 3 of 27
Version 1.1
Author: A Mak a.k.a. Makuk
A photo of the bottom PCB where the antenna cable is connected (top right).
By A. Mak 24-10-2008 - Page 4 of 27
Version 1.1
Author: A Mak a.k.a. Makuk
Another photo of the top PCB (top view).
By A. Mak 24-10-2008 - Page 5 of 27
[ Pobierz całość w formacie PDF ]