HYGAL98GBB, alarmy, schematy pl
[ Pobierz całość w formacie PDF ]
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
HYUNDAI
MOD.
GALLOPER
YEAR
98
fi
PETROL
DIESEL
X
MAKE
ALARM/SIREN
POSITION
Position the compact alarms and the sirens in the engine compartment, on the
wheelhouse, passenger’s side. Pass the cables through the original rubber sleeve
on the right of the servobrake.
POWER SUPPLY
+ 30:
connect to the general supply wiring located in the multiway connector at the
entrance of the fuse box.
- 31:
connect with a ring terminal to one of the terminals coming out of the general
power supply behind the left lateral panel, driver’s side.
IGNITION WIRE
+ 15/54:
connect to the 2 mm
2
BLACK/WHITE wire in the wiring harness coming
out of the 6 way connector, near the steering column.
DIRECTION INDICATORS
Connect to the 1 mm
2
GREEN/YELLOW and GREEN/LIGHT BLUE wires located
in the wiring harness coming out of the 21 way connector near the steering column.
ELECTRIC WINDOWS
Positive control signal
Front window, driver’s side:
cut the BLUE/WHITE wire directly in the wiring harness coming out of the driver’s
side door switch.
Front window, passenger’s side:
cut the LIGHT BLUE/GREEN wire located in the wiring harness coming out of the
core hitch of the driver’s side door.
CENTRAL DOORS LOCKING Additional motor
It is necessary to install a 2 wires motor (Art.1060) as the driver’s side door is not
provided with an actuating device.
IMMOBILISATION POINT
Fuel pump
Cut the BLACK/WHITE wire located in the wiring harness coming out of the 6 way
connector, in the electrovalve unit, in the engine compartment.
STARTER
+50:
Cut the 2 mm
2
BLACK/YELLOW wire located in the wiring harness coming
out of the 6 way connector under the steering column.
BONNET SWITCH
Install an additional switch on the headlamp support plate, in correspondence with
the left lateral lamp.
DOORS SWITCH
Connect to the RED/GREEN wire located in the wiring harness coming out of the
16 way white connector and going out of the white central unit, under the fuse box
in the lower part of the dashboard, driver’s side.
BOOT SWITCH
It is necessary to install an additonal switch as the vehicle has no connection point.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
hygal98gbb.doc
[ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV. 00
www.cobra.it
HYUNDAI
MOD.
GALLOPER
YEAR
98
fi
PETROL
DIESEL
X
MAKE
ALARM/SIREN
POSITION
Position the compact alarms and the sirens in the engine compartment, on the
wheelhouse, passenger’s side. Pass the cables through the original rubber sleeve
on the right of the servobrake.
POWER SUPPLY
+ 30:
connect to the general supply wiring located in the multiway connector at the
entrance of the fuse box.
- 31:
connect with a ring terminal to one of the terminals coming out of the general
power supply behind the left lateral panel, driver’s side.
IGNITION WIRE
+ 15/54:
connect to the 2 mm
2
BLACK/WHITE wire in the wiring harness coming
out of the 6 way connector, near the steering column.
DIRECTION INDICATORS
Connect to the 1 mm
2
GREEN/YELLOW and GREEN/LIGHT BLUE wires located
in the wiring harness coming out of the 21 way connector near the steering column.
ELECTRIC WINDOWS
Positive control signal
Front window, driver’s side:
cut the BLUE/WHITE wire directly in the wiring harness coming out of the driver’s
side door switch.
Front window, passenger’s side:
cut the LIGHT BLUE/GREEN wire located in the wiring harness coming out of the
core hitch of the driver’s side door.
CENTRAL DOORS LOCKING Additional motor
It is necessary to install a 2 wires motor (Art.1060) as the driver’s side door is not
provided with an actuating device.
IMMOBILISATION POINT
Fuel pump
Cut the BLACK/WHITE wire located in the wiring harness coming out of the 6 way
connector, in the electrovalve unit, in the engine compartment.
STARTER
+50:
Cut the 2 mm
2
BLACK/YELLOW wire located in the wiring harness coming
out of the 6 way connector under the steering column.
BONNET SWITCH
Install an additional switch on the headlamp support plate, in correspondence with
the left lateral lamp.
DOORS SWITCH
Connect to the RED/GREEN wire located in the wiring harness coming out of the
16 way white connector and going out of the white central unit, under the fuse box
in the lower part of the dashboard, driver’s side.
BOOT SWITCH
It is necessary to install an additonal switch as the vehicle has no connection point.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed
as per the instructions given on the product installation manual.
hygal98gbb.doc
[ Pobierz całość w formacie PDF ]