HM1140C-TE, MAKITA Budowa, Instrukcje serwisowe
[ Pobierz całość w formacie PDF ]
//-->TECHNICAL INFORMATIONModels No.DescriptionHM1140CDEMOLITION HAMMER98mm (3-7/8")New ToolModel HM1140C is the sister version of the existing Model HM1100C,HM1140C is for 3/4" Hex. 21/32" Round shank bit (BOSCH type). Its briefbenefits are;Bit can be installed by sliding Tool holdercover, and machining mark on chuckand groove on Bit.*Superior protection from dust by anti-dust Tool holder cap*Electrical speed control features*Variable speed control*Soft start*Steady speed517mm"(20-3/8)SpecificationsVoltage (V)100115200220230240No load speedBit TypeNet weightCord lengthCurrent (A)11.09.65.55.04.84.6Cycle (Hz)50/6050/6050/6050/6050/6050/60Continuous Rating (W)InputOutput105045010504501050450105045010504501050450Max.Output(W)1050105010501050105010501300-2600 bpm3/4" Hex 21/32" Round shank bit6.3kg (13.9 lbs)5m (16.4 ft)Standard equipmentGrease Vessel (Bit grease)----------1pc.1 pc. (100g) (0.22 lbs)Plastic Carrying Case----------------1pc.(HP2032 only)[Note] The standard equipment may differ from country to country.Optional accessoriesBull point 19-300Bull Point 19-450Cold Chisel 26-300Cold Chisel 26-450Scaling Chisel 50-300Grooving Chisel 22-300Grooving Chisel 26-300Clay Spade 105-400Rammer 140Bushing ToolGround Rod Adapter 20Blow-out Bulb 64Grease Vessel (30g)224mm)(8-7/8"CONCEPTION AND MAIN APPLICATIONSRepairProcedures other than below are same as for HM1100C.Disassembly and assembly of tool holder.(1) DisassemblyPull off tool holder cover by one hand (1) and remove toolholder cap by the other hand (2). Then remove O-ring 29 (3)and take the tool holder apart.2Tool holdercap1Tool holdercover3O-ring 29(2) Assembly1. Fix roller guide with pin 6 as shown in the right figure.Pin 6Roller guideTool holder2. Align notch on the tool holder cover to the position of pin 6and set the tool holder cover on (1). Insert the pin 6 into theroller guide (2) and pull down the tool holder cover, thenattach the O-ring 29 and the tool holder cap.Tool holder cover12Roller guideTool holdercoverAlign thisRoller guidePin 63. Align projection on the surface of the tool holder cap with thenotch of the tool holder cover and assemble them. After thismake sure that the tool holder cap does not rotate.Align thisGrease up point (x mark) (Points differing from HM1100C are shown.)(1) DisassemblyPull off tool holder cover by one hand (1) and remove toolholder cap by the other hand (2). Then remove O-ring 29 (3)and take the tool holder apart.Makita Grease N No.2Roller 2Makita Grease R No.00Whole circumstance on O-ring 22 inside the sleeve guideInterchangeability between HM1100(C) and HM1130(C)(1) StrikerTake care that the striker of HM1100(C) and HM1130(C) cannot be used to HM1140C.There is a step.44.0mm38.0mmHM1140CHM1100(C)HM1130(C)(2) Tool holder supportTool holder support of HM1100(C) cannot be used because it's length is 4mm longer.87.5mmHM1140C83.5mmHM1100(C)(3) Sleeve guideHM1140C uses the same sleeve guide as of HM1130(C). The sleeve guide for HM1100(C) cannot be used.HM1140CHM1130(C)HM1100(C)(4) Parts other than listed below are common to HM1100(C).HM1140C uses the same sleeve guide as of HM1130(C). The sleeve guide for HM1100(C) cannot be used.Tool holder cap,Tool holder support,Compression spring 47Tool holder cove,Roller 12Sleeve guidTool holderRoller guidStriker44.0mmWiring diagramWithouto Noise SuppressorControllerPower P2supplycordP1SwitchRed6 43 1ConnectorBlackBlackWhite (Brown)OrangeFieldWith Noise SuppressorNoisesuppressorPowersupplycordP2Switch6 43 1ControllerRedWhite (Brown)OrangeConnectorBlackCHOrangeBlackP1Choke oil(Lead wire)FieldLead holder in case P.N.6451055 condenser is usedSwitchVariable resistorPower supply cordDon't put the lead wires on the rib.Lead holder in case P.N.6452001 condenser is usedPickup coil lead wiresVariable resistor lead wiresLead wire (red)Lead wire (white or brown)TubeBlanket holder lead wire (orang)In case choke coilis usedControllerControllerPut controller lead wires (white or brown and red) andbrush holder lead wire (orange) into the left lead holder.Place power supply cord top of the other lead wires andput it into the right lead holder.Put variable resistor lead wires into the right lead holdertogether with a tube.Variable resistor lead wires should hold pickup coillead wires.Lead wires should not be loose in the motor housing.Setting pickup coilLibChoke coilPut it intolead holderLead wire shouldpass outside the libPickup coilDon't cross the leadwires in the hole. [ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
//-->TECHNICAL INFORMATIONModels No.DescriptionHM1140CDEMOLITION HAMMER98mm (3-7/8")New ToolModel HM1140C is the sister version of the existing Model HM1100C,HM1140C is for 3/4" Hex. 21/32" Round shank bit (BOSCH type). Its briefbenefits are;Bit can be installed by sliding Tool holdercover, and machining mark on chuckand groove on Bit.*Superior protection from dust by anti-dust Tool holder cap*Electrical speed control features*Variable speed control*Soft start*Steady speed517mm"(20-3/8)SpecificationsVoltage (V)100115200220230240No load speedBit TypeNet weightCord lengthCurrent (A)11.09.65.55.04.84.6Cycle (Hz)50/6050/6050/6050/6050/6050/60Continuous Rating (W)InputOutput105045010504501050450105045010504501050450Max.Output(W)1050105010501050105010501300-2600 bpm3/4" Hex 21/32" Round shank bit6.3kg (13.9 lbs)5m (16.4 ft)Standard equipmentGrease Vessel (Bit grease)----------1pc.1 pc. (100g) (0.22 lbs)Plastic Carrying Case----------------1pc.(HP2032 only)[Note] The standard equipment may differ from country to country.Optional accessoriesBull point 19-300Bull Point 19-450Cold Chisel 26-300Cold Chisel 26-450Scaling Chisel 50-300Grooving Chisel 22-300Grooving Chisel 26-300Clay Spade 105-400Rammer 140Bushing ToolGround Rod Adapter 20Blow-out Bulb 64Grease Vessel (30g)224mm)(8-7/8"CONCEPTION AND MAIN APPLICATIONSRepairProcedures other than below are same as for HM1100C.Disassembly and assembly of tool holder.(1) DisassemblyPull off tool holder cover by one hand (1) and remove toolholder cap by the other hand (2). Then remove O-ring 29 (3)and take the tool holder apart.2Tool holdercap1Tool holdercover3O-ring 29(2) Assembly1. Fix roller guide with pin 6 as shown in the right figure.Pin 6Roller guideTool holder2. Align notch on the tool holder cover to the position of pin 6and set the tool holder cover on (1). Insert the pin 6 into theroller guide (2) and pull down the tool holder cover, thenattach the O-ring 29 and the tool holder cap.Tool holder cover12Roller guideTool holdercoverAlign thisRoller guidePin 63. Align projection on the surface of the tool holder cap with thenotch of the tool holder cover and assemble them. After thismake sure that the tool holder cap does not rotate.Align thisGrease up point (x mark) (Points differing from HM1100C are shown.)(1) DisassemblyPull off tool holder cover by one hand (1) and remove toolholder cap by the other hand (2). Then remove O-ring 29 (3)and take the tool holder apart.Makita Grease N No.2Roller 2Makita Grease R No.00Whole circumstance on O-ring 22 inside the sleeve guideInterchangeability between HM1100(C) and HM1130(C)(1) StrikerTake care that the striker of HM1100(C) and HM1130(C) cannot be used to HM1140C.There is a step.44.0mm38.0mmHM1140CHM1100(C)HM1130(C)(2) Tool holder supportTool holder support of HM1100(C) cannot be used because it's length is 4mm longer.87.5mmHM1140C83.5mmHM1100(C)(3) Sleeve guideHM1140C uses the same sleeve guide as of HM1130(C). The sleeve guide for HM1100(C) cannot be used.HM1140CHM1130(C)HM1100(C)(4) Parts other than listed below are common to HM1100(C).HM1140C uses the same sleeve guide as of HM1130(C). The sleeve guide for HM1100(C) cannot be used.Tool holder cap,Tool holder support,Compression spring 47Tool holder cove,Roller 12Sleeve guidTool holderRoller guidStriker44.0mmWiring diagramWithouto Noise SuppressorControllerPower P2supplycordP1SwitchRed6 43 1ConnectorBlackBlackWhite (Brown)OrangeFieldWith Noise SuppressorNoisesuppressorPowersupplycordP2Switch6 43 1ControllerRedWhite (Brown)OrangeConnectorBlackCHOrangeBlackP1Choke oil(Lead wire)FieldLead holder in case P.N.6451055 condenser is usedSwitchVariable resistorPower supply cordDon't put the lead wires on the rib.Lead holder in case P.N.6452001 condenser is usedPickup coil lead wiresVariable resistor lead wiresLead wire (red)Lead wire (white or brown)TubeBlanket holder lead wire (orang)In case choke coilis usedControllerControllerPut controller lead wires (white or brown and red) andbrush holder lead wire (orange) into the left lead holder.Place power supply cord top of the other lead wires andput it into the right lead holder.Put variable resistor lead wires into the right lead holdertogether with a tube.Variable resistor lead wires should hold pickup coillead wires.Lead wires should not be loose in the motor housing.Setting pickup coilLibChoke coilPut it intolead holderLead wire shouldpass outside the libPickup coilDon't cross the leadwires in the hole. [ Pobierz całość w formacie PDF ]