HM1400-TE, MAKITA Budowa, Instrukcje serwisowe
[ Pobierz całość w formacie PDF ]
//-->TECHNICAL INFORMATIONModels No.DescriptionHM 1400MAKITA Electric Breaker510New ToolCONCEPTION AND MAIN APPLICATIONSThis product is the one remodeled from8600Swith double insulation to comply with therequest from overseas in order to increasesales. This is the model for export, which hasbeen developed for sales promotion.223SpecificationsVoltage(V)100115200220230240Blows per minuteTool sizeUseNet Weight(kg)Cord length(m)Current(A)13116.55.95.75.4Frequency(Hz)50-6050-6050-6050-6050-6050-60Consumedpower(W)124012401240124012401240Ratedoutput(W)660660660660660660Max.output(W)1000100010001000100010001200 min30mm hex.For striking(chisel finishing by bull point, cold chisel or scalingchisel, ground digging by shovel, leveling by rammer etc.)17kg5mStandard equipmentHexagonal spanner 5,6Bull point 30-410Wooden boxOptional accessoriesBull pointCold chiselScaling chiselShovelRammer etc.Common to 8600S, HM1300, HM1301The standard equipment for the tools shown may differ form country to country613Repair1. Replacement of armature and fieldDisassembly: follow the next procedure(1) Take off E-ring, switch lever pin andswitch lever from the handle.(2) Take off two hexagon socket boltsM8x40 for mounting handle L and pullout handle sleeve more than 2mm.(3) Remove three pan head machine screwsM5x30 mounting handle L and handle R.Then, take out handle L.(4) Take off field lead wire from the switch terminal.(5) Take off two hexagon socket boltsM8x40 for mounting handle R and takeout handle R from crank housing.Holder cap plateRear caseHexagon socket bolts M6X35Handle sleeveHexagon socketbolts M8X40E-ringSwitch lever pinSwitch leverHandle LHandle R(6) Remove holder cap plate, holder cap and carbon brushes.(7) Take off four hexagon socket boltsM6x35 for mounting rear case and remove rear case.(8) Tap crank housing by resin hammer to remove motor housing.(9) Motor housing, field, and armature are removed together.Then, disassemble them in the same way as in other models.Assembly: Follow the opposite procedure to the disassembly. Make sure of the following points;(1) Mount screw seal to armature.Screw seal(2) First insert armature to crank housing,then insert motor housing.(3) Be sure to insert flat washer 24 at assembling rear case.Ensure the mounting direction of rear case.(4) Be sure of mounting field lead wire without slack.2. Other procedures in disassembly and assembly are the same as in #8600S.projected part downwardFlat washer 24 on the inside [ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
//-->TECHNICAL INFORMATIONModels No.DescriptionHM 1400MAKITA Electric Breaker510New ToolCONCEPTION AND MAIN APPLICATIONSThis product is the one remodeled from8600Swith double insulation to comply with therequest from overseas in order to increasesales. This is the model for export, which hasbeen developed for sales promotion.223SpecificationsVoltage(V)100115200220230240Blows per minuteTool sizeUseNet Weight(kg)Cord length(m)Current(A)13116.55.95.75.4Frequency(Hz)50-6050-6050-6050-6050-6050-60Consumedpower(W)124012401240124012401240Ratedoutput(W)660660660660660660Max.output(W)1000100010001000100010001200 min30mm hex.For striking(chisel finishing by bull point, cold chisel or scalingchisel, ground digging by shovel, leveling by rammer etc.)17kg5mStandard equipmentHexagonal spanner 5,6Bull point 30-410Wooden boxOptional accessoriesBull pointCold chiselScaling chiselShovelRammer etc.Common to 8600S, HM1300, HM1301The standard equipment for the tools shown may differ form country to country613Repair1. Replacement of armature and fieldDisassembly: follow the next procedure(1) Take off E-ring, switch lever pin andswitch lever from the handle.(2) Take off two hexagon socket boltsM8x40 for mounting handle L and pullout handle sleeve more than 2mm.(3) Remove three pan head machine screwsM5x30 mounting handle L and handle R.Then, take out handle L.(4) Take off field lead wire from the switch terminal.(5) Take off two hexagon socket boltsM8x40 for mounting handle R and takeout handle R from crank housing.Holder cap plateRear caseHexagon socket bolts M6X35Handle sleeveHexagon socketbolts M8X40E-ringSwitch lever pinSwitch leverHandle LHandle R(6) Remove holder cap plate, holder cap and carbon brushes.(7) Take off four hexagon socket boltsM6x35 for mounting rear case and remove rear case.(8) Tap crank housing by resin hammer to remove motor housing.(9) Motor housing, field, and armature are removed together.Then, disassemble them in the same way as in other models.Assembly: Follow the opposite procedure to the disassembly. Make sure of the following points;(1) Mount screw seal to armature.Screw seal(2) First insert armature to crank housing,then insert motor housing.(3) Be sure to insert flat washer 24 at assembling rear case.Ensure the mounting direction of rear case.(4) Be sure of mounting field lead wire without slack.2. Other procedures in disassembly and assembly are the same as in #8600S.projected part downwardFlat washer 24 on the inside [ Pobierz całość w formacie PDF ]