HP P2055 p2035, Regeneracja tonerów
[ Pobierz całość w formacie PDF ]
HPP2055TECH
Technical Instructions
Printers
Cartridge Info
Tools
1
HP LaserJet P2035 printer
(CE461A)
HP LaserJet P2035n printer
(CE462A)
CE505A 2,300 pgs
(for both HP LaserJet P2035
and HP LaserJet P2055)
Drill
3/32-inch Drill Bit
3/8-inch Drill Bit
3/4-inch Hole Saw with
Pilot Drill Bit
Needle-nose Pliers
Scratch Awl
Small, Flat-blade
Screwdriver
Phillips Screwdriver
Putty Knife with stiff
blade, 1 1/4” wide
Utility Knife
X-Acto Knife
Drum Drive Axle Removal
Tool
Ohmmeter
Supplies Required:
99% Alcohol
Conductive Grease
Cotton Swabs
Lint-free Cloth
Padding Powder
Drum
Toner
Wiper Blade
Chip
Fill Plug
(HP1505FILLPLUG or
HP2600FILLPLUG)
3 screws
CORPORATE
LOS ANGELES, USA
US 1 800 394.9900
Int’l +1 818 837.8100
FAX 1 800 394.9910
Int’l +1 818 838.7047
KANSAS CITY, USA
US 1 913 871.1700
FAX 1 913 888.0626
NEW YORK, USA
US 1 800 431.7884
Int’l +1 631 588.7300
FAX 1 800 431.8812
Int’l +1 631 588.7333
CE505X 6500 pgs
(only for HP LaserJet P2055)
HP LaserJet P2055dn printer
(CE459A)
HP LaserJet P2055x printer
(CE460A)
Photo 1
Step 1
If the OPC drum is going to be replaced, use
Drum Drive Axle Removal Tool to remove
the drum drive axle
(See photo 1).
You will
install it later on a new drum. To remove the
drive axle, insert the C-shaped claw of the
tool under the drive flange of the axle and
use the lip on the drum end plate as a lever-
age to pry the drive axle out
(See photos 2
& 3).
MIAMI, USA
US 1 800 595.4297
Int’l +1 305 594.3396
FAX 1 800 522.8640
Int’l +1 305 594.3309
TORONTO, CAN
CAN 1 877 848.0818
Int’l +1 905 712.9501
FAX 1 877 772.6773
Int’l +1 905 712.9502
PHOTO 2
MELBOURNE, AUS
AUS 1 800 003. 100
Int’l +62 03 9561.8102
FAX 1 800 004.302
Int’l +62 03 9561-7751
SYDNEY, AUS
AUS 1 800 003.100
Int’l +62 02 9648.2630
FAX 1800 004.302
Int’l +62 02 9548.2635
BUENOS AIRES, ARG
ARG 0810 444.2656
Int’l +011 4583.5900
FAX +011 4584.3100
PHOTO 3
SÃO PAULO, BRAZIL
Int’l +55 11 5524.8000
BOGOTÁ, COLOMBIA
Int'l +57 1410.8842
CALI, COLOMBIA
Int'l +57 2661.1166
MONTERREY, MEXICO
Int' +52 55 5333.9800
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX +27 11 974.3593
ZHUHAI, PR CHINA
Int’l +86 756 3359608
FAX +86 756 3359681
© 2009 Future Graphics Imaging Corporation. All rights reserved. Future Graphics Imaging Corporation (FGIC) is a distributor of compati-
ble replacement parts and products for imaging equipment. None of FGIC's products are genuine OEM replacement parts and no affiliation
or sponsorship is to be implied between FGIC and any OEM.
E-mail: info@fgimaging.com
Website: www.fgimaging.com
REV. 04/13/09
2
HP LaserJet P2055 Technical Instructions
PHOTO 7
Step 3
Insert a flat screwdriver between drum con-
tact end and waste hopper and carefully pry
out the drum contact axle
(See photo 7).
Step 2
Using a scratch awl, carefully pry the
cartridge pins out of the cartridge
(See photo 4).
Grab the pins with
needle-nose pliers and remove them
(See photo 5).
PHOTO 4
PHOTO 8
Step 4
Using needle-nose pliers, remove the drum
contact axle
(See photo 8).
PHOTO 5
PHOTO 9
Step 5
Carefully lift up on the contact end of the
drum and remove the drum out of the drum
end plate
(See photo 9).
If the drum is going
to be reused, place it in a protected area
away from light.
Step 2
Separate the two sections of the car-
tridge
(See photo 6).
Set the toner
hopper aside.
PHOTO 10
Step 6
Lift out the PCR
(See photo 10).
Clean the
PCR using a dry lint-free cloth.
PHOTO 6
PHOTO 11
Step 7
Remove two screws holding the wiper blade
(See photo 11).
© 2009 Future Graphics Imaging Corporation. All
rights reserved. Future Graphics Imaging
Corporation (FGIC) is a distributor of compatible
replacement parts and products for imaging equip-
ment. None of FGIC's products are genuine OEM
replacement parts and no affiliation or sponsorship
is to be implied between FGIC and any OEM.
HP LaserJet P2055 Technical Instructions
3
PHOTO 12
Step 8
Remove the wiper blade
(See photo 12).
Clean the waste hopper using dry, com-
pressed air or a vacuum.
Step 14
Using an X-acto knife, cut the plastic
weld holding the chip in place
(See
photo 17).
Install the new chip onto
the cartridge. Set the waste hopper
aside in a protected area away from
light.
PHOTO 13
Step 9
Apply padding powder to a new or once-
used wiper blade. Place the blade onto the
waste hopper and install the two screws
that hold the blade in place
(See photo 13).
PHOTO 17
PHOTO 14
NOTE: If you don't plan to seal the
toner unit, do not remove the con-
tact end cap. Remove the gear
housing end cap instead. Use the
same procedure as in steps 19-21
to remove the gear housing end
cap.
Step 10
Clean the PCR saddles using a cotton
swab. Apply new conductive grease to the
black conductive saddle. Install the clean
PCR
(See photo 14).
Step 15
The contact end cap on the toner
hopper is sonically welded to the
toner hopper. Using a utility knife,
cut off the plastic welds on contact
end cap
(See photo 18).
PHOTO 15
Step 11
Apply padding powder to the drum.
Carefully slide the drum into the drum end
plate
(See photo 15).
PHOTO 18
PHOTO 16
Step 12
Install the drum contact axle
(See photo 16).
Step 13
Rotate the drum to ensure that the drum
and wiper blade are properly lubricated.
Clean the padding powder off the PCR
using a lint-free cloth.
© 2009 Future Graphics Imaging Corporation. All
rights reserved. Future Graphics Imaging
Corporation (FGIC) is a distributor of compatible
replacement parts and products for imaging equip-
ment. None of FGIC's products are genuine OEM
replacement parts and no affiliation or sponsorship
is to be implied between FGIC and any OEM.
4
HP LaserJet P2055 Technical Instructions
PHOTO 21
Step 18
The alignment pin holding the contact side
mag roller arm is sonically welded to the
toner hopper. Insert a small, flat-blade
screwdriver between the contact side mag
roller arm and the toner hopper. Carefully
pry the contact side mag roller arm away
from the toner hopper
(See photo 21).
Remove the end cap.
Step 16
Using a 3/32-inch drill bit, drill a hole
into the contact end cap where the
two plastic welds hold the end cap
to the toner hopper
(See photo 19).
PHOTO 19
PHOTO 22
Step 19
Remove the mag roller from the toner hop-
per
(See photo 22).
Remove the mag roller
drive gear from the toner hopper
(See photo
23).
Step 17
Insert a putty knife blade between
the toner hopper and the contact
end cap next to the sonic welds.
Carefully pry the end cap away from
the toner hopper
(See photo 20).
PHOTO 23
PHOTO 20
PHOTO 24
Step 20
Remove the mag roller bushings from the
ends of the mag roller. Clean the mag roller
first with compressed air or a vacuum, then
using a dry lint-free cloth. Clean the mag
roller bushings using a lint-free cloth.
Step 21
Remove the two screws holding the doctor
blade
(See photo 24).
PHOTO 25
Step 22
Remove the plastic scrapers from the ends
of the doctor blade and remove the blade
(See photo 25).
Clean the doctor blade
using a lint-free cloth. Empty the remaining
toner from the toner hopper. Clean the toner
hopper using dry, compressed air or a vac-
uum.
© 2009 Future Graphics Imaging Corporation. All
rights reserved. Future Graphics Imaging
Corporation (FGIC) is a distributor of compatible
replacement parts and products for imaging equip-
ment. None of FGIC's products are genuine OEM
replacement parts and no affiliation or sponsorship
is to be implied between FGIC and any OEM.
HP LaserJet P2055 Technical Instructions
5
PHOTO 26
Step 23
Remove the white plastic bar that is
attached to the top of the mag roller open-
ing with a flat-blade screwdriver or a utility
knife
(See photo 26).
Step 27
Mark the center of the hole on the
flat surface of the contact side of the
toner hopper with a scratch awl
(See
photo 31).
PHOTO 31
PHOTO 27
Step 24
Remove the doctor blade end foams from
each side of the toner hopper
(See photo
27).
Step 28
Using a 3/4-inch hole saw with pilot
drill bit, drill a hole applying light
pressure to prevent the hole saw
from grabbing and damaging the
toner hopper
(See photo 32).
Step 29
Clean the toner hopper using dry
compressed air, making sure the
hopper is void of plastic shavings.
PHOTO 28
Step 25
To make a toner fill hole in CE505A car-
tridge, use 3/8-inch drill bit. Mark the center
of the hole on the flat surface of the top side
of the toner hopper with a scratch awl
(See
photo 28).
Make sure to position the hole
between the ribs of the hopper.
RIBS
PHOTO 32
PHOTO 29
Step 26
Drill a hole into the toner hopper using light
pressure to start the hole
(See photo 29).
NOTE: Too much pressure could cause
drill bit to grab and damage the hopper.
To make a toner fill hole in CE505X cartridge
use the same procedure as in steps 28 and
29 to make a fill hole using 3/8-inch drill bit
(See photo 30).
Alternatively, use a 3/4-inch hole saw with
pilot drill bit to drill a hole into the contact
side of the toner hopper:
PHOTO 30
© 2009 Future Graphics Imaging Corporation. All
rights reserved. Future Graphics Imaging
Corporation (FGIC) is a distributor of compatible
replacement parts and products for imaging equip-
ment. None of FGIC's products are genuine OEM
replacement parts and no affiliation or sponsorship
is to be implied between FGIC and any OEM.
[ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
HPP2055TECH
Technical Instructions
Printers
Cartridge Info
Tools
1
HP LaserJet P2035 printer
(CE461A)
HP LaserJet P2035n printer
(CE462A)
CE505A 2,300 pgs
(for both HP LaserJet P2035
and HP LaserJet P2055)
Drill
3/32-inch Drill Bit
3/8-inch Drill Bit
3/4-inch Hole Saw with
Pilot Drill Bit
Needle-nose Pliers
Scratch Awl
Small, Flat-blade
Screwdriver
Phillips Screwdriver
Putty Knife with stiff
blade, 1 1/4” wide
Utility Knife
X-Acto Knife
Drum Drive Axle Removal
Tool
Ohmmeter
Supplies Required:
99% Alcohol
Conductive Grease
Cotton Swabs
Lint-free Cloth
Padding Powder
Drum
Toner
Wiper Blade
Chip
Fill Plug
(HP1505FILLPLUG or
HP2600FILLPLUG)
3 screws
CORPORATE
LOS ANGELES, USA
US 1 800 394.9900
Int’l +1 818 837.8100
FAX 1 800 394.9910
Int’l +1 818 838.7047
KANSAS CITY, USA
US 1 913 871.1700
FAX 1 913 888.0626
NEW YORK, USA
US 1 800 431.7884
Int’l +1 631 588.7300
FAX 1 800 431.8812
Int’l +1 631 588.7333
CE505X 6500 pgs
(only for HP LaserJet P2055)
HP LaserJet P2055dn printer
(CE459A)
HP LaserJet P2055x printer
(CE460A)
Photo 1
Step 1
If the OPC drum is going to be replaced, use
Drum Drive Axle Removal Tool to remove
the drum drive axle
(See photo 1).
You will
install it later on a new drum. To remove the
drive axle, insert the C-shaped claw of the
tool under the drive flange of the axle and
use the lip on the drum end plate as a lever-
age to pry the drive axle out
(See photos 2
& 3).
MIAMI, USA
US 1 800 595.4297
Int’l +1 305 594.3396
FAX 1 800 522.8640
Int’l +1 305 594.3309
TORONTO, CAN
CAN 1 877 848.0818
Int’l +1 905 712.9501
FAX 1 877 772.6773
Int’l +1 905 712.9502
PHOTO 2
MELBOURNE, AUS
AUS 1 800 003. 100
Int’l +62 03 9561.8102
FAX 1 800 004.302
Int’l +62 03 9561-7751
SYDNEY, AUS
AUS 1 800 003.100
Int’l +62 02 9648.2630
FAX 1800 004.302
Int’l +62 02 9548.2635
BUENOS AIRES, ARG
ARG 0810 444.2656
Int’l +011 4583.5900
FAX +011 4584.3100
PHOTO 3
SÃO PAULO, BRAZIL
Int’l +55 11 5524.8000
BOGOTÁ, COLOMBIA
Int'l +57 1410.8842
CALI, COLOMBIA
Int'l +57 2661.1166
MONTERREY, MEXICO
Int' +52 55 5333.9800
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX +27 11 974.3593
ZHUHAI, PR CHINA
Int’l +86 756 3359608
FAX +86 756 3359681
© 2009 Future Graphics Imaging Corporation. All rights reserved. Future Graphics Imaging Corporation (FGIC) is a distributor of compati-
ble replacement parts and products for imaging equipment. None of FGIC's products are genuine OEM replacement parts and no affiliation
or sponsorship is to be implied between FGIC and any OEM.
E-mail: info@fgimaging.com
Website: www.fgimaging.com
REV. 04/13/09
2
HP LaserJet P2055 Technical Instructions
PHOTO 7
Step 3
Insert a flat screwdriver between drum con-
tact end and waste hopper and carefully pry
out the drum contact axle
(See photo 7).
Step 2
Using a scratch awl, carefully pry the
cartridge pins out of the cartridge
(See photo 4).
Grab the pins with
needle-nose pliers and remove them
(See photo 5).
PHOTO 4
PHOTO 8
Step 4
Using needle-nose pliers, remove the drum
contact axle
(See photo 8).
PHOTO 5
PHOTO 9
Step 5
Carefully lift up on the contact end of the
drum and remove the drum out of the drum
end plate
(See photo 9).
If the drum is going
to be reused, place it in a protected area
away from light.
Step 2
Separate the two sections of the car-
tridge
(See photo 6).
Set the toner
hopper aside.
PHOTO 10
Step 6
Lift out the PCR
(See photo 10).
Clean the
PCR using a dry lint-free cloth.
PHOTO 6
PHOTO 11
Step 7
Remove two screws holding the wiper blade
(See photo 11).
© 2009 Future Graphics Imaging Corporation. All
rights reserved. Future Graphics Imaging
Corporation (FGIC) is a distributor of compatible
replacement parts and products for imaging equip-
ment. None of FGIC's products are genuine OEM
replacement parts and no affiliation or sponsorship
is to be implied between FGIC and any OEM.
HP LaserJet P2055 Technical Instructions
3
PHOTO 12
Step 8
Remove the wiper blade
(See photo 12).
Clean the waste hopper using dry, com-
pressed air or a vacuum.
Step 14
Using an X-acto knife, cut the plastic
weld holding the chip in place
(See
photo 17).
Install the new chip onto
the cartridge. Set the waste hopper
aside in a protected area away from
light.
PHOTO 13
Step 9
Apply padding powder to a new or once-
used wiper blade. Place the blade onto the
waste hopper and install the two screws
that hold the blade in place
(See photo 13).
PHOTO 17
PHOTO 14
NOTE: If you don't plan to seal the
toner unit, do not remove the con-
tact end cap. Remove the gear
housing end cap instead. Use the
same procedure as in steps 19-21
to remove the gear housing end
cap.
Step 10
Clean the PCR saddles using a cotton
swab. Apply new conductive grease to the
black conductive saddle. Install the clean
PCR
(See photo 14).
Step 15
The contact end cap on the toner
hopper is sonically welded to the
toner hopper. Using a utility knife,
cut off the plastic welds on contact
end cap
(See photo 18).
PHOTO 15
Step 11
Apply padding powder to the drum.
Carefully slide the drum into the drum end
plate
(See photo 15).
PHOTO 18
PHOTO 16
Step 12
Install the drum contact axle
(See photo 16).
Step 13
Rotate the drum to ensure that the drum
and wiper blade are properly lubricated.
Clean the padding powder off the PCR
using a lint-free cloth.
© 2009 Future Graphics Imaging Corporation. All
rights reserved. Future Graphics Imaging
Corporation (FGIC) is a distributor of compatible
replacement parts and products for imaging equip-
ment. None of FGIC's products are genuine OEM
replacement parts and no affiliation or sponsorship
is to be implied between FGIC and any OEM.
4
HP LaserJet P2055 Technical Instructions
PHOTO 21
Step 18
The alignment pin holding the contact side
mag roller arm is sonically welded to the
toner hopper. Insert a small, flat-blade
screwdriver between the contact side mag
roller arm and the toner hopper. Carefully
pry the contact side mag roller arm away
from the toner hopper
(See photo 21).
Remove the end cap.
Step 16
Using a 3/32-inch drill bit, drill a hole
into the contact end cap where the
two plastic welds hold the end cap
to the toner hopper
(See photo 19).
PHOTO 19
PHOTO 22
Step 19
Remove the mag roller from the toner hop-
per
(See photo 22).
Remove the mag roller
drive gear from the toner hopper
(See photo
23).
Step 17
Insert a putty knife blade between
the toner hopper and the contact
end cap next to the sonic welds.
Carefully pry the end cap away from
the toner hopper
(See photo 20).
PHOTO 23
PHOTO 20
PHOTO 24
Step 20
Remove the mag roller bushings from the
ends of the mag roller. Clean the mag roller
first with compressed air or a vacuum, then
using a dry lint-free cloth. Clean the mag
roller bushings using a lint-free cloth.
Step 21
Remove the two screws holding the doctor
blade
(See photo 24).
PHOTO 25
Step 22
Remove the plastic scrapers from the ends
of the doctor blade and remove the blade
(See photo 25).
Clean the doctor blade
using a lint-free cloth. Empty the remaining
toner from the toner hopper. Clean the toner
hopper using dry, compressed air or a vac-
uum.
© 2009 Future Graphics Imaging Corporation. All
rights reserved. Future Graphics Imaging
Corporation (FGIC) is a distributor of compatible
replacement parts and products for imaging equip-
ment. None of FGIC's products are genuine OEM
replacement parts and no affiliation or sponsorship
is to be implied between FGIC and any OEM.
HP LaserJet P2055 Technical Instructions
5
PHOTO 26
Step 23
Remove the white plastic bar that is
attached to the top of the mag roller open-
ing with a flat-blade screwdriver or a utility
knife
(See photo 26).
Step 27
Mark the center of the hole on the
flat surface of the contact side of the
toner hopper with a scratch awl
(See
photo 31).
PHOTO 31
PHOTO 27
Step 24
Remove the doctor blade end foams from
each side of the toner hopper
(See photo
27).
Step 28
Using a 3/4-inch hole saw with pilot
drill bit, drill a hole applying light
pressure to prevent the hole saw
from grabbing and damaging the
toner hopper
(See photo 32).
Step 29
Clean the toner hopper using dry
compressed air, making sure the
hopper is void of plastic shavings.
PHOTO 28
Step 25
To make a toner fill hole in CE505A car-
tridge, use 3/8-inch drill bit. Mark the center
of the hole on the flat surface of the top side
of the toner hopper with a scratch awl
(See
photo 28).
Make sure to position the hole
between the ribs of the hopper.
RIBS
PHOTO 32
PHOTO 29
Step 26
Drill a hole into the toner hopper using light
pressure to start the hole
(See photo 29).
NOTE: Too much pressure could cause
drill bit to grab and damage the hopper.
To make a toner fill hole in CE505X cartridge
use the same procedure as in steps 28 and
29 to make a fill hole using 3/8-inch drill bit
(See photo 30).
Alternatively, use a 3/4-inch hole saw with
pilot drill bit to drill a hole into the contact
side of the toner hopper:
PHOTO 30
© 2009 Future Graphics Imaging Corporation. All
rights reserved. Future Graphics Imaging
Corporation (FGIC) is a distributor of compatible
replacement parts and products for imaging equip-
ment. None of FGIC's products are genuine OEM
replacement parts and no affiliation or sponsorship
is to be implied between FGIC and any OEM.
[ Pobierz całość w formacie PDF ]