HR5000-TE, MAKITA Budowa, Instrukcje serwisowe
[ Pobierz całość w formacie PDF ]
//-->TECHNICAL INFORMATIONModels No.DescriptionHR5000MAKITA Rotary hammerHR5000...476HR5000K...489New ToolCONCEPT AND MAIN APPLICATIONSThe purpose of developing this machine is that it should be aslight as #HR3850. And with the same capacity to bore andchisel as that of #8050. You can change [Rotation+Hammering]to [Hammering Only] easily by operating the lever. Grease PackSystem is applied for lubrication. The shank of attachingtools for #HR5000 is in common with Bosch Spline Shaft type,and #HR5000K is in common with Kungo hexagonal shaft typerespectively.110SpecificationsVoltage (V)100115200220230240Current (A)14.011.06.35.75.45.2Cycle(Hz)50/6050/6050/6050/6050/6050/60Continuous ratingInput(W)Output(W)132073012006001200600120060012006001200600260/min2100/min50mm150mm255mm9.6kg9.7kg5mMax. Output(W)140014001400140014001400No load speed (R.P.M.)Blows per minute (/min.)T.C.T. bitMax.Core bitcapacity (mm)Net weight (kg)HR5000HR5000KPower supply cord (m)for concretefor Hume concrete pipeStandard equipmentHex. spanner 4Hex. spanner 5Hex. spanner 6Optional accessoriesReffer to General catalogueThe standard equipment for the tools shown may differ form country to country.266REPAIR1. Principal tools to be prepared(1) Vice fixed on the work table(2) Pipe wrench( 60cm or more, the longer it may be, the easier for operation).(3) Backplate a) Copper plate, 2pcs (Used when put Clunk Housing between Vices)b) Iron plates, 2pcs of the dimensions in the illustration(Used whenput Cylinderliner between vices)20mm(4) Bullpoint2. DisassemblyA) How to remove Tool Holder(left screw) and BarrelAs you see the right illustration, put a backplate(copper plate) on the side of Clunk Housing(for protection of Clunk Housing), fix it by Vice,and put two Sides of Bullpoint inserted intoTool Holder by pipe wrench ,then turn it to rightCopper platePut a piece of wood toassist the Vise pertormance.B) How to remove Cylinder liner(right screw) and Hexagonal nutAs you see the right illustration, put a backplate onBecomes loose by left turntwo sides of Cylinder liner, fix it by Vice, hold twosides of Hexagonal nut by pipe wrench, and turn it toBackplaseleft.Note 1) If the screws did not loosen in disassemblingof A)and B), heat the screw part over thegas stove about five minutes to 200- 250 C.Then, it will be loose because the adhesiveeffect becomes weak.C) How to remove Clunk ShaftMake the Clunk Cap side of Clunk Housingdownward, press the end face of Clunk Shaft by rborPress, and it will come out.Ballbearing3. AssemblyA) How to fasten Cylinder Liner and Hexagonal NutFlat Washer1 ) Remove grease from Screw part, and apply Primer T747 (Note2) .2 ) Insert Flat Washer and Ballbearing3 ) When the surface applied Primer gets dry(in about 3-5 minutes),apply Locktight 648 , three lines (Note 3)Apply Primer and Locktibht4 ) Fasten Hexagonal Nut (Width between two faces:41mm)by 2000-2500kgf.cm(with 60-cm pipe wrench,approx. 33kgf. Strength)Note2) Primer T747 is hardening promotion agent to shorten the time forhardening Locktight648(adhesive).AdhesiveNote3) Three lines mean to apply the adhesivethree times in the shaft direction.B) How to fasten Tool Retainer and Hexagonal Nut1 ) Remove grease in Screw part2 ) Apply Locktight 648 two lines(times).3 ) Fasten Hexagonal Nut (Width between twofaces:13mm)with 250-300kgf.cmAt 10cm, strenght of approx. 25kg.fJIS spanner 13C) How to fasten Tool Holder and Barrel1 ) Remove grease in Screw part2 ) Apply Screw Lock Super1342 two times.3 ) Fasten with 3000-3500kgf.cm. ( Approx. 50kgf strenght by 60-cm pipe wrench)D) In Oil Seal, Y Ring and O Ring, etc., apply grease on Lip parts and attach carefully so that it may not bedamaged.E) After assembling, enclose MAKITA GREASE R No.00, 75-80 g(the vakue when there is no grease inHousing) from Clunk Cap part.4. The assembly and disassembly except the above are almost the same as those of #HR3850. [ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
//-->TECHNICAL INFORMATIONModels No.DescriptionHR5000MAKITA Rotary hammerHR5000...476HR5000K...489New ToolCONCEPT AND MAIN APPLICATIONSThe purpose of developing this machine is that it should be aslight as #HR3850. And with the same capacity to bore andchisel as that of #8050. You can change [Rotation+Hammering]to [Hammering Only] easily by operating the lever. Grease PackSystem is applied for lubrication. The shank of attachingtools for #HR5000 is in common with Bosch Spline Shaft type,and #HR5000K is in common with Kungo hexagonal shaft typerespectively.110SpecificationsVoltage (V)100115200220230240Current (A)14.011.06.35.75.45.2Cycle(Hz)50/6050/6050/6050/6050/6050/60Continuous ratingInput(W)Output(W)132073012006001200600120060012006001200600260/min2100/min50mm150mm255mm9.6kg9.7kg5mMax. Output(W)140014001400140014001400No load speed (R.P.M.)Blows per minute (/min.)T.C.T. bitMax.Core bitcapacity (mm)Net weight (kg)HR5000HR5000KPower supply cord (m)for concretefor Hume concrete pipeStandard equipmentHex. spanner 4Hex. spanner 5Hex. spanner 6Optional accessoriesReffer to General catalogueThe standard equipment for the tools shown may differ form country to country.266REPAIR1. Principal tools to be prepared(1) Vice fixed on the work table(2) Pipe wrench( 60cm or more, the longer it may be, the easier for operation).(3) Backplate a) Copper plate, 2pcs (Used when put Clunk Housing between Vices)b) Iron plates, 2pcs of the dimensions in the illustration(Used whenput Cylinderliner between vices)20mm(4) Bullpoint2. DisassemblyA) How to remove Tool Holder(left screw) and BarrelAs you see the right illustration, put a backplate(copper plate) on the side of Clunk Housing(for protection of Clunk Housing), fix it by Vice,and put two Sides of Bullpoint inserted intoTool Holder by pipe wrench ,then turn it to rightCopper platePut a piece of wood toassist the Vise pertormance.B) How to remove Cylinder liner(right screw) and Hexagonal nutAs you see the right illustration, put a backplate onBecomes loose by left turntwo sides of Cylinder liner, fix it by Vice, hold twosides of Hexagonal nut by pipe wrench, and turn it toBackplaseleft.Note 1) If the screws did not loosen in disassemblingof A)and B), heat the screw part over thegas stove about five minutes to 200- 250 C.Then, it will be loose because the adhesiveeffect becomes weak.C) How to remove Clunk ShaftMake the Clunk Cap side of Clunk Housingdownward, press the end face of Clunk Shaft by rborPress, and it will come out.Ballbearing3. AssemblyA) How to fasten Cylinder Liner and Hexagonal NutFlat Washer1 ) Remove grease from Screw part, and apply Primer T747 (Note2) .2 ) Insert Flat Washer and Ballbearing3 ) When the surface applied Primer gets dry(in about 3-5 minutes),apply Locktight 648 , three lines (Note 3)Apply Primer and Locktibht4 ) Fasten Hexagonal Nut (Width between two faces:41mm)by 2000-2500kgf.cm(with 60-cm pipe wrench,approx. 33kgf. Strength)Note2) Primer T747 is hardening promotion agent to shorten the time forhardening Locktight648(adhesive).AdhesiveNote3) Three lines mean to apply the adhesivethree times in the shaft direction.B) How to fasten Tool Retainer and Hexagonal Nut1 ) Remove grease in Screw part2 ) Apply Locktight 648 two lines(times).3 ) Fasten Hexagonal Nut (Width between twofaces:13mm)with 250-300kgf.cmAt 10cm, strenght of approx. 25kg.fJIS spanner 13C) How to fasten Tool Holder and Barrel1 ) Remove grease in Screw part2 ) Apply Screw Lock Super1342 two times.3 ) Fasten with 3000-3500kgf.cm. ( Approx. 50kgf strenght by 60-cm pipe wrench)D) In Oil Seal, Y Ring and O Ring, etc., apply grease on Lip parts and attach carefully so that it may not bedamaged.E) After assembling, enclose MAKITA GREASE R No.00, 75-80 g(the vakue when there is no grease inHousing) from Clunk Cap part.4. The assembly and disassembly except the above are almost the same as those of #HR3850. [ Pobierz całość w formacie PDF ]