HP3005 Q51A-X, Regeneracja tonerów
[ Pobierz całość w formacie PDF ]
HPP3005TECH
Technical Instructions
Printers
OEM Info
Tools
1
CORPORATE
LOS ANGELES, USA
HP P3005
HP P3005/d
HP P3005/n
HP P3005/dn
HP P3005/x
Q7551A
Black
(Standard Capacity – 6.5K pages)
Tools & Supplies Needed:
Tools required:
#1 Phillips Screwdriver
Small Flat Blade Screwdriver
Drill and Drill Bit-3/32”
Spring Hook, Pliers
Wire Cutters
US 1 800 394.9900
Int’l +1 818 837.8100
FAX 1 800 394.9910
Int’l +1 818 838.7047
Q7551X
Black
(High Capacity – 13K pages)
ATLANTA, USA
US 1 877 676.4223
Int’l +1 678 919.1189
FAX 1 877 337.7976
Int’l +1 770 516.7794
Supplies Required:
Padding Powder
Soft Lint-Free Cloth
Cotton Swabs
Conductive Grease
Anhydrous Isopropyl Alcohol
MAGCLEANER
Vacuum or dry Compressed Air
KANSAS CITY, USA
US 1 913 871.1700
FAX 1 913 888.0626
Photo 1
MIAMI, USA
US 1 800 595.4297
Int’l +1 305 594.3396
FAX 1 800 522.8640
Int’l +1 305 594.3309
Step 1
Position cartridge with label facing you. Locate
the cartridge pin covers.
(See Photo 1)
NEW YORK, USA
US 1 800 431.7884
Int’l +1 631 588.7300
FAX 1 800 431.8812
Int’l +1 631 588.7333
TORONTO, CAN
CAN 1 877 848.0818
Int’l +1 905 712.9501
FAX 1 877 772.6773
Int’l +1 905 712.9502
BUENOS AIRES, ARG
ARG 0810 444.2656
Int’l +011 4583.5900
FAX +011 4584.3100
Photo 2
Step 2
Using a drill with a 3/32” drill bit.
(See Photo 2)
MELBOURNE, AUS
AUS 1 800 003. 100
Int’l +62 03 9561.8102
FAX 1 800 004.302
Int’l +62 03 9561-7751
Drill a hole on the inside edge of the opening to
expose the end of the cartridge pin.
(See Photo 3)
Use a spring hook or comparable tool with angled
end to push the cartridge pin past the edge of the
cartridge. Pull the pin out using wire cutters.
(See Photo 4)
SYDNEY, AUS
AUS 1 800 003.100
Int’l +62 02 9648.2630
FAX 1800 004.302
Int’l +62 02 9548.2635
MONTEVIDEO, URY
URY 02 902.2001
Int’l +5982 902.2001
FAX +5982 900.0858
Photo 4
Photo 3
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX +27 11 974.3593
SÃO PAULO, BRAZIL
Int’l +55 11 5524.8000
RAANANA, ISRAEL
ISR 09 760.12.39
Int’l +972 9760.12.39
ISR 052.38.555.82
Int’l +972 5238.555.82
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
REV. 12/22/06
2
HPP3005 Technical Instructions
Photo 8
Step 6
Remove PCR roller from saddle blocks.
Set PCR roller aside.
(See Photo 8)
Step 3
Separate the cartridge and put aside
the toner unit.
(See Photo 5)
Photo 5
Photo 9
Step 7
Remove the screws to the wiper blade and
remove wiper blade. Clean waste toner area
using a vacuum or dry, compressed air.
(See Photo 9)
Step 4
Remove the drum axial and contact
cover. Carefully pull on the contact
cover using a pliers removing the
drum axial and spring loaded contact
cover.
(See Photos 6 & 7)
NOTE: Be careful not to lose the con-
tact cover coil spring.
Photo 10
Step 8
Clean wiper blade with a soft, dry cloth.
(See Photo 10)
Apply padding powder to the blade edge and
reinstall wiper blade.
(See Photo 11)
Photo 6
Photo 11
Step 9
Clean PCR saddle blocks with cotton swab
and Anhydrous Isopropyl Alcohol. Clean PCR
using a dry, soft, lint-free cloth.
(See Photo 12)
NOTE:
If needed, de-ionized water can be
used to clean the PCR.
(See Photo 13)
Photo 7
Photo 13
Photo 12
Step 5
Remove the drum and set aside in a
light protected area.
HPP3005 Technical Instructions
3
Photo 14
Step 10
Apply conductive grease to the black PCR
saddle block.
(See Photo 14
)
Install PCR into saddle blocks.
(See Photo 15
)
Step 14
Starting on the toner unit, locate the
cartridge handle and label to face
you. Remove the right side drum
shutter guide bar from the holder.
Remove the spring loaded guide
arm using small blade screw driver.
Remove left side guide bar from the
holder.
NOTE:
Drum shutter must be
closed to remove guide arm. Do not
loose guide arm spring.
(See Photo 20)
Photo 15
Photo 20
Photo 16
Step 11
Clean drum using soft, dry cloth.
(See Photo 16)
Apply padding powder to the drum.
(See Photo 17)
Photo 17
Step 15
Remove the two screws holding the
drive gear cover. Remove drive
gear cover and mag roller gear. Set
aside cover and gear for later.
(See Photo 21)
Photo 18
Step 12
Install the drum by inserting the drum axle and
contact cover into the contact side of the drum.
(See Photo 18)
Align contact cover and coil spring arm to the
PCR contact and arm locator slot. Rotate drum
to ensure smooth operation.
(See Photo 19)
Remove excess padding powder using a soft,
dry cloth from the drum and PCR area. Move
contact cover to ensure correct spring opera-
tion.
Photo 21
Photo 19
Step 13
Set aside the waste unit. Protect the drum from
light exposure.
4
HPP3005 Technical Instructions
Photo 24
Step 18
Clean mag roller using soft cloth and
MAGCLEANER.
(See Photo 24)
Step 16
Remove the two screws holding the
mag contact cover and remove
cover. Remove the mag roller taking
care not to damage the spring con-
tact. Clean excess toner by blowing
dry, compressed air over the mag
roller.
(See Photo 22)
Clean the spring contact with alcohol and a
soft cloth or cotton swabs. Set aside mag roller
until later.
(See Photo 25)
Photo 25
Photo 22
Photo 26
Step 19
Clean the contact side end cap with alcohol.
(See Photo 26)
Step 17
Remove and inspect the green and
black bushings on the mag roller.
Replace the bushings if they are
worn or cracked.
(See Photo 23)
Inspect white bushing, if warn or damaged
replace bushing.
Photo 23
Add conductive grease to contact.
(See Photo 27)
Photo 27
Step 20
Remove the two screws holding the doctor
blade.
(See Photo 28)
Clean using a soft, dry cloth.
(See Photo 29)
Photo 28
Photo 28
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
HPP3005 Technical Instructions
5
Photo 30
Step 21
Fill toner hopper with HP P3005 type toner
through the mag roller opening. Use up to 340
grams of toner for the 51A cartridge and 600
grams of toner for the 51X cartridge (prelimi-
nary fill weights).
(See Photo 30
)
Step 25
Install mag roller drive gear.
(See Photo 36)
Inspect gears in the
drive gear end cap, ensure they are
clean. Install drive gear end cap.
(See Photo 37)
Photo 31
Step 22
Replace the doctor blade using the two screws
and white end pieces.
(See Photo 31)
Photo 36
Photo 36
Photo 32
Step 23
Reassemble mag roller.
(See Photo 32)
Black bushing is on the contact side and green
bushing is on the gear side.
(See Photo 33)
Gear side mag roller arm has a bearing that
requires inspection and replacement if worn
or damaged. Place mag roller into toner unit.
(See Photo 34)
Photo 34
Photo 33
Photo 35
Step 24
Install contact end cap using the two mounting
screws. Be careful not to damage mag roller
spring contact.
(See Photo 35)
[ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
HPP3005TECH
Technical Instructions
Printers
OEM Info
Tools
1
CORPORATE
LOS ANGELES, USA
HP P3005
HP P3005/d
HP P3005/n
HP P3005/dn
HP P3005/x
Q7551A
Black
(Standard Capacity – 6.5K pages)
Tools & Supplies Needed:
Tools required:
#1 Phillips Screwdriver
Small Flat Blade Screwdriver
Drill and Drill Bit-3/32”
Spring Hook, Pliers
Wire Cutters
US 1 800 394.9900
Int’l +1 818 837.8100
FAX 1 800 394.9910
Int’l +1 818 838.7047
Q7551X
Black
(High Capacity – 13K pages)
ATLANTA, USA
US 1 877 676.4223
Int’l +1 678 919.1189
FAX 1 877 337.7976
Int’l +1 770 516.7794
Supplies Required:
Padding Powder
Soft Lint-Free Cloth
Cotton Swabs
Conductive Grease
Anhydrous Isopropyl Alcohol
MAGCLEANER
Vacuum or dry Compressed Air
KANSAS CITY, USA
US 1 913 871.1700
FAX 1 913 888.0626
Photo 1
MIAMI, USA
US 1 800 595.4297
Int’l +1 305 594.3396
FAX 1 800 522.8640
Int’l +1 305 594.3309
Step 1
Position cartridge with label facing you. Locate
the cartridge pin covers.
(See Photo 1)
NEW YORK, USA
US 1 800 431.7884
Int’l +1 631 588.7300
FAX 1 800 431.8812
Int’l +1 631 588.7333
TORONTO, CAN
CAN 1 877 848.0818
Int’l +1 905 712.9501
FAX 1 877 772.6773
Int’l +1 905 712.9502
BUENOS AIRES, ARG
ARG 0810 444.2656
Int’l +011 4583.5900
FAX +011 4584.3100
Photo 2
Step 2
Using a drill with a 3/32” drill bit.
(See Photo 2)
MELBOURNE, AUS
AUS 1 800 003. 100
Int’l +62 03 9561.8102
FAX 1 800 004.302
Int’l +62 03 9561-7751
Drill a hole on the inside edge of the opening to
expose the end of the cartridge pin.
(See Photo 3)
Use a spring hook or comparable tool with angled
end to push the cartridge pin past the edge of the
cartridge. Pull the pin out using wire cutters.
(See Photo 4)
SYDNEY, AUS
AUS 1 800 003.100
Int’l +62 02 9648.2630
FAX 1800 004.302
Int’l +62 02 9548.2635
MONTEVIDEO, URY
URY 02 902.2001
Int’l +5982 902.2001
FAX +5982 900.0858
Photo 4
Photo 3
JOHANNESBURG, S.A.
S.A. +27 11 974.6155
FAX +27 11 974.3593
SÃO PAULO, BRAZIL
Int’l +55 11 5524.8000
RAANANA, ISRAEL
ISR 09 760.12.39
Int’l +972 9760.12.39
ISR 052.38.555.82
Int’l +972 5238.555.82
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
REV. 12/22/06
2
HPP3005 Technical Instructions
Photo 8
Step 6
Remove PCR roller from saddle blocks.
Set PCR roller aside.
(See Photo 8)
Step 3
Separate the cartridge and put aside
the toner unit.
(See Photo 5)
Photo 5
Photo 9
Step 7
Remove the screws to the wiper blade and
remove wiper blade. Clean waste toner area
using a vacuum or dry, compressed air.
(See Photo 9)
Step 4
Remove the drum axial and contact
cover. Carefully pull on the contact
cover using a pliers removing the
drum axial and spring loaded contact
cover.
(See Photos 6 & 7)
NOTE: Be careful not to lose the con-
tact cover coil spring.
Photo 10
Step 8
Clean wiper blade with a soft, dry cloth.
(See Photo 10)
Apply padding powder to the blade edge and
reinstall wiper blade.
(See Photo 11)
Photo 6
Photo 11
Step 9
Clean PCR saddle blocks with cotton swab
and Anhydrous Isopropyl Alcohol. Clean PCR
using a dry, soft, lint-free cloth.
(See Photo 12)
NOTE:
If needed, de-ionized water can be
used to clean the PCR.
(See Photo 13)
Photo 7
Photo 13
Photo 12
Step 5
Remove the drum and set aside in a
light protected area.
HPP3005 Technical Instructions
3
Photo 14
Step 10
Apply conductive grease to the black PCR
saddle block.
(See Photo 14
)
Install PCR into saddle blocks.
(See Photo 15
)
Step 14
Starting on the toner unit, locate the
cartridge handle and label to face
you. Remove the right side drum
shutter guide bar from the holder.
Remove the spring loaded guide
arm using small blade screw driver.
Remove left side guide bar from the
holder.
NOTE:
Drum shutter must be
closed to remove guide arm. Do not
loose guide arm spring.
(See Photo 20)
Photo 15
Photo 20
Photo 16
Step 11
Clean drum using soft, dry cloth.
(See Photo 16)
Apply padding powder to the drum.
(See Photo 17)
Photo 17
Step 15
Remove the two screws holding the
drive gear cover. Remove drive
gear cover and mag roller gear. Set
aside cover and gear for later.
(See Photo 21)
Photo 18
Step 12
Install the drum by inserting the drum axle and
contact cover into the contact side of the drum.
(See Photo 18)
Align contact cover and coil spring arm to the
PCR contact and arm locator slot. Rotate drum
to ensure smooth operation.
(See Photo 19)
Remove excess padding powder using a soft,
dry cloth from the drum and PCR area. Move
contact cover to ensure correct spring opera-
tion.
Photo 21
Photo 19
Step 13
Set aside the waste unit. Protect the drum from
light exposure.
4
HPP3005 Technical Instructions
Photo 24
Step 18
Clean mag roller using soft cloth and
MAGCLEANER.
(See Photo 24)
Step 16
Remove the two screws holding the
mag contact cover and remove
cover. Remove the mag roller taking
care not to damage the spring con-
tact. Clean excess toner by blowing
dry, compressed air over the mag
roller.
(See Photo 22)
Clean the spring contact with alcohol and a
soft cloth or cotton swabs. Set aside mag roller
until later.
(See Photo 25)
Photo 25
Photo 22
Photo 26
Step 19
Clean the contact side end cap with alcohol.
(See Photo 26)
Step 17
Remove and inspect the green and
black bushings on the mag roller.
Replace the bushings if they are
worn or cracked.
(See Photo 23)
Inspect white bushing, if warn or damaged
replace bushing.
Photo 23
Add conductive grease to contact.
(See Photo 27)
Photo 27
Step 20
Remove the two screws holding the doctor
blade.
(See Photo 28)
Clean using a soft, dry cloth.
(See Photo 29)
Photo 28
Photo 28
E-mail: info@futuregraphicsllc.com
Website:
www.futuregraphicsllc.com
HPP3005 Technical Instructions
5
Photo 30
Step 21
Fill toner hopper with HP P3005 type toner
through the mag roller opening. Use up to 340
grams of toner for the 51A cartridge and 600
grams of toner for the 51X cartridge (prelimi-
nary fill weights).
(See Photo 30
)
Step 25
Install mag roller drive gear.
(See Photo 36)
Inspect gears in the
drive gear end cap, ensure they are
clean. Install drive gear end cap.
(See Photo 37)
Photo 31
Step 22
Replace the doctor blade using the two screws
and white end pieces.
(See Photo 31)
Photo 36
Photo 36
Photo 32
Step 23
Reassemble mag roller.
(See Photo 32)
Black bushing is on the contact side and green
bushing is on the gear side.
(See Photo 33)
Gear side mag roller arm has a bearing that
requires inspection and replacement if worn
or damaged. Place mag roller into toner unit.
(See Photo 34)
Photo 34
Photo 33
Photo 35
Step 24
Install contact end cap using the two mounting
screws. Be careful not to damage mag roller
spring contact.
(See Photo 35)
[ Pobierz całość w formacie PDF ]